How to Winterize Sprinkler System Lines, Valves and Backflow Before a Freeze

Table of Contents

Water expands by about one-eleventh when it freezes, according to Colorado State University Extension. In a sprinkler system, that’s enough to split valves, crack fittings and pop sprinkler bodies. You won’t see the damage until spring, when a zone floods the flower bed or doesn’t come on at all.

How you winterize a sprinkler system depends on two things: how cold your winters get, and what kind of backflow device you have. Get the second one wrong and the air compressor can ruin your backflow preventer in seconds.

Quick Answer: To winterize a sprinkler system, shut off the irrigation water supply, then remove the water from every zone. In cold climates, Colorado State University Extension says the only reliable way is a compressed-air blowout, one zone at a time, at 40 to 80 PSI (no more than 80 PSI for rigid PVC or 50 PSI for polyethylene). Never blow air through a PVB or RP backflow preventer; drain it and leave its valves half open. In mild climates like most of Texas, Texas A&M says shutting off the water, insulating exposed pipe and draining above-ground parts is usually enough.

Do Lawn Sprinklers Need to Be Winterized? Cold vs. Warm Climates

If the ground freezes down to your buried pipes, yes, and the job is a full blowout. If you only get light, short freezes, the job is much smaller.

Texas A&M’s irrigation program draws that line clearly. The blowout method is mostly used in the northern U.S., where the ground freezes to pipe depth, and most Texas systems aren’t designed for one. For light to mild freezes, Texas A&M’s list is four steps: turn off the controller, shut off the irrigation water, insulate above-ground PVC, and drain above-ground parts like the backflow assembly.

If you’re still deciding whether your climate needs it at all, our guide on whether you should winterize your sprinkler system walks through it by region.

Your winterWhat to doSource
Ground freezes to pipe depth (northern U.S., mountain West)Shut off water, compressed-air blowout of every zone, drain backflowColorado State
Light to mild freezes (most of Texas, much of the South)Controller off, water off, insulate exposed PVC, drain backflow and above-ground partsTexas A&M
Basic system with drain valves, moderate coldWater off, release pressure in each zone, open drains; blow out if there are no drainsUtah State

When to Winterize Sprinkler System Lines

Before your first hard freeze, not after it. There’s no single date that works nationwide. Use your local forecast and your lawn’s needs together: cool-season grass still benefits from water through early fall, so most northern homeowners shut down once nights start dropping into the 20s or a hard freeze is in the forecast.

Two practical points:

  • Book early if you’re hiring. Blowout crews fill their calendars in October in cold states. Search interest for “sprinkler blowout” peaks in October, which tells you everyone else is calling at the same time.
  • Don’t wait for a warm afternoon after a freeze. If water has already frozen in an above-ground backflow device, the damage may be done.

Step 1: Shut Off the Water and Set the Controller

Find the irrigation shutoff. Colorado State says there should be a stop and waste valve or similar drain between the water supply and the backflow device. It may be in a basement, a crawlspace, or a valve box underground, sometimes 5 feet down, which takes a long valve key. Colorado State’s advice: don’t force it.

Then the controller. Here the sources split:

  • Utah State University and Texas A&M say to set the controller to off.
  • Colorado State says to leave it powered, because the transformer’s heat helps keep moisture and corrosion out, and to program a minimum cycle once a week so solenoid plungers don’t stick.

Our take: if your controller lives in a heated garage or basement, “off” or rain mode is fine. If it’s in an unheated spot or outdoors, Colorado State’s approach of leaving it powered is the safer bet. Either way, the water supply is off, so nothing flows.

Step 2: How to Winterize a Sprinkler System With an Air Compressor

This is the blowout, and it’s where most of the damage happens when people improvise.

Size the Compressor by Airflow, Not Just PSI

Colorado State says air volume matters as much as pressure. Too little air and it rides over the water instead of pushing it out, leaving puddles in low spots that freeze anyway.

The sizing rule: divide the gallons per minute (GPM) of your biggest zone by 7.5 to get the cubic feet per minute (CFM) you need. Colorado State’s example: a zone running 20 GPM needs about 2.66 CFM. Zone GPM should be on your irrigation plan, or you can add up the nozzle ratings from the manufacturer.

A quick field test from the same guide: if the sprinkler heads stay popped up and air keeps flowing after the water clears, your compressor is the right size.

Set the Right Pressure

PipeMax blowout pressure (Colorado State)
Rigid PVC (white)80 PSI
Polyethylene (flexible black)50 PSI
Ideal working range40 to 80 PSI

Use a regulator on the compressor. Colorado State warns that pressure above the nozzle rating can blow nozzles off, so check your heads’ rating too.

Blow Out One Zone at a Time

  1. Connect the compressor to the blowout fitting downstream of the backflow device, and make sure the downstream ball valve on the backflow is closed. Colorado State says to use a metal fitting if you can, since it dissipates heat better than PVC.
  2. Start the zone farthest from the compressor at the controller.
  3. Turn on the air and run it until only mist comes out of the heads.
  4. Move to the next zone.
  5. Do every zone twice, in two short cycles, rather than one long one, per Colorado State.
  6. Once a zone is dry, stop. Colorado State says air moving through dry pipe builds friction and heat that can melt fittings.
  7. Never open more zones than you’d normally run at once. More zones means more velocity and more heat.

Wear eye protection the whole time; Colorado State lists it as its final caution. And keep pets inside. The same guide notes the whistling can spook them.

Step 3: Drain the Backflow Preventer by Type (AVB, Pressure Vacuum Breaker, RP)

The backflow device is the part most likely to crack and the part most often damaged by a careless blowout. What you do depends on which one you have.

DeviceWhat it looks likeHow to winterize (Colorado State)
Atmospheric vacuum breaker (AVB)Small device after each zone valveCleared with compressed air when that zone is blown out
Pressure vacuum breaker (PVB)Single above-ground assembly with two ball valves and test cocksNever blow out. Drain, then exercise ball valves and test cocks and leave them half open
Reduced pressure (RP)Larger assembly with two check valves and a relief portNever blow out. Drain each check zone, leave ball valves at about 45 degrees

Why never blow air through a PVB or RP? Colorado State says the rubber seals inside can melt from the heat of the air.

Why half open? Ball valves left fully closed or fully open can trap water that freezes and splits the body. Half open lets it drain.

Insulate the assembly afterward with a backflow cover or foam wrap if it sits above ground. Texas A&M lists insulating exposed PVC as a core step even in mild climates.

How to Winterize Sprinkler System Without a Blowout: Drain Valves

You can, but know the limits.

Utah State University Extension’s basic method: shut off the main valve, set the controller to off, turn on each valve to release pressure, and open the drain valves if your system has them. If there are no drains, Utah State says to use an air compressor or have a professional blow it out.

Manual drain valves sit at the low points of each zone; you open them by hand. Automatic drain valves open on their own when pressure drops. Both rely on gravity.

Colorado State doesn’t recommend relying on them in freezing climates. Pipes shift over time, low spots trap water, and there’s no way to inspect buried lines once you’re done. It also says systems with electric valves must be blown out, because that’s the only way to clear the water sitting on top of the valve diaphragm.

So: drain valves alone are reasonable in mild climates or on systems designed for them. Where the ground freezes hard, plan on a blowout.

At What Temperature Will My Sprinkler Pipes Freeze?

Water freezes at 32°F, but buried pipe doesn’t freeze the moment the air does. Soil insulates lines underground, which is why Texas A&M’s mild-climate steps focus on what’s above ground: the backflow assembly, exposed PVC and risers. Those parts are the first to freeze on a cold night.

How Long Will Sprinklers Freeze at 29 Degrees?

There’s no fixed number of hours. It depends on wind, sun, whether the part is insulated, and whether water is sitting in it. A drained, insulated backflow device can ride out a night in the 20s; a full, exposed one may not. That’s the logic behind Texas A&M’s approach: drain and insulate the exposed parts before a freeze, even if you aren’t doing a full winterization.

Should You DIY or Hire a Pro?

DIY works if you have a compressor with enough CFM, a regulator, and a clear idea of your backflow type. Colorado State says you can do it yourself with the right equipment and knowledge. Utah State suggests a professional if you’re unsure.

Where we’d hire: an RP device, a big system with many zones, or a small pancake compressor that can’t keep up. A rented tow-behind compressor and a cracked backflow can quickly cost more than the service.

LawnGuru’s sprinkler winterization service averages $80, with most jobs between $51 and $111, depending on the number of zones.

How Much Should It Cost to Winterize Your Sprinkler System?

Through LawnGuru, the average is $80 and the normal range is $51 to $111. Zone count is the main factor. Our sprinkler winterization cost guide breaks down what drives the price.

Spring Start-Up: Undo It Carefully

Colorado State’s spring steps for a PVB: close the test cocks and ball valves, turn the water supply on, then open the ball valves slowly to pressurize the system. Slow is the point. Opening fast causes water hammer, which can damage the same parts you just protected.

Then run each zone, look for geysers, leaks and soggy spots, and reset your watering schedule. Our guide on how long to water grass with a sprinkler helps with run times.

Frequently Asked Questions

What PSI should I use to blow out sprinklers?

Colorado State says 40 to 80 PSI, with 80 PSI as the maximum for rigid PVC and 50 PSI for polyethylene pipe. Check your nozzle ratings too.

Can I blow out a sprinkler system with a small air compressor?

It may reach the pressure but not the airflow. Divide your largest zone’s GPM by 7.5 to see the CFM you need, per Colorado State. An undersized compressor takes longer and can leave water in low spots.

Should I turn off my sprinkler controller in winter?

Utah State and Texas A&M say to turn it off. Colorado State says to leave it powered for its transformer heat and run a weekly minimum cycle. Either works once the water is off; leaving it powered matters more if the controller is outdoors or unheated.

Do I need to winterize drip irrigation?

Yes, in freezing climates. Colorado State Extension notes that drip systems with many right-angle fittings can hold water and may need pressurized air to clear. Use the low end of the pressure range for drip tubing.

What if I forgot to winterize and it already froze?

Don’t turn the water on yet. Wait for a thaw, then check the backflow device and exposed pipe for cracks before pressurizing. If anything looks split, have it repaired first, or the first spring start-up will find the leak for you.

Do I need to winterize a sprinkler system in Texas?

Usually not with a full blowout. Texas A&M says most Texas systems aren’t designed for one; turn off the controller and water, insulate exposed PVC, and drain the backflow assembly before a freeze.

$29 Lawn Mowing Service - No Contracts - Skip or Cancel Service Anytime

Easily hire the best lawn & landscape pros working in your neighborhood.